Crankshaft High-end Swiing (ZA50 engine)∙ Suitable for Puch X30 NG-2AH, Puch X30 N-2A, Puch Maxi S 2AH and Puch Supermaxi LG2 mopeds.
∙ Complete with needlebearing.
∙ Full round crankshaft for high performance engines.
∙…

Crankshaft (ZA50 engine)∙ Suitable for Puch X30 NG-2AH, Puch X30 N-2A, Puch Maxi S 2AH and Puch Supermaxi LG2 mopeds.
∙ Complete with needlebearing.
∙ Diameter brass bush:9,5mm (clutch bell with a inside diameter of 9,5mm…

Crankshaft Swiing (ZA50 engine)∙ Suitable for Puch X30 NG-2AH, Puch X30 N-2A, Puch Maxi S 2AH and Puch Supermaxi LG2 mopeds.
∙ Complete with needlebearing.
∙ Diameter brass bush:10,2 mm (clutch bell with a inside diameter of…

Clutch first gear (ZA50 engine)∙ For ZA50 engines.
∙ Clutch for the first gear.
∙ Original Surflex Puch part.

Clutch second gear (ZA50 engine)∙ For ZA50 engines.
∙ Clutch for the second gear.
∙ Original Surflex Puch part.

Gasket set (ZA50 engine)

∙ For Puch ZA50 engine.
∙ Crank case gasket.
∙ Clutch-cover gasket.

Crank case gasket (ZA50 engine)∙ For ZA50 engines.
∙ Crank case gasket.

Clutch cover gasket (ZA50 engine)∙ For ZA50 engine.
∙ Clutch cover gasket.

Clutch cover bolt set (ZA50 engine)∙ For ZA50 engine.
∙ Clutch cover bolt set.
∙ Flat head.

Engine case bolt set complete (ZA50 engine)

∙ For ZA50 engine.
∙ Engine case bolt set.
∙ Complete set.
∙ Flat head.

Engine case bolt set (ZA50 engine)

∙ For ZA50 engine.
∙ Engine case bolt set.
∙ Flat head.

Seal set Viton (ZA50 engine)∙ For ZA50 engine.

Complete set with:

∙ 1x Crankshaft seal right side 20/35/7.
∙ 1x Crankshaft seal left side 17/35/7.

Seal set complete (ZA50 engine)

∙ For ZA50 engine.

Complete set with:

∙ 1x Crankshaft seal right side 20/35/7
∙ 1x Crankshaft seal left side 17/35/7
∙ 1x front sprocket seal 25/35/7

Crankshaft seal 17x35x7 Viton (ZA50 engine)∙ For ZA50/Z50 engines.
∙ Crankshaft seal.
∙ 17x35x7.
∙ Viton.
∙ Extremely heat resistant.

Suitable for:

∙ Crankshaft left and right side Z50 engine.
∙ Crankshaft left…

Crankshaft seal 17x35x7 (ZA50/Z50 engine)∙ For ZA50/Z50 engines.
∙ 17x35x7.
∙ Double lip.
∙ Crankshaft seal.

Crankshaft seal 20x35x7 (ZA50 engine)∙ For ZA50 engine.
∙ 20x35x7.
∙ Crankshaft seal.

Crankshaft seal right side 20x35x7 Viton (ZA50 engine)∙ For ZA50 engine.
∙ 20x35x7.
∙ Viton.
∙ Extremely heat resistant.

Suitable for:

∙ Crankshaft right side ZA50 engine.

Sprocket shaft seal 25x35x7 B1 (ZA50 engine)∙ For ZA50 engine.
∙ 25x35x7.
∙ Sprocket shaft seal.

Bearing set with shift bearings (ZA50 engine)Complete bearing set thats needed for a Puch ZA50 engine.

∙ 1x E20 Ball bearing.
∙ 1x L17 Ball bearing (A-Qaulity NSK)
∙ 1X 6203 C3 Ball bearing.
∙ 1x 6005 Ball bearing.
∙ 1x…

Bearing set (ZA50 engine)Bearing set thats needed for a Puch ZA50 engine.

∙ 1x E20 Ball bearing.
∙ 1x L17 Ball bearing (A-Qaulity NSK)
∙ 1X 6203 C3 Ball bearing.
∙ 1x 6005 Ball bearing.
∙ 1x 6002 Ball bearing.
∙ 1x…

Crankshaft bearing L17 NSK (ZA50/Z50 engine)∙ Crankshaft bearing L17.
∙ A Piece.
∙ NSK.

Suitable for:

∙ ZA50 engine.
∙ Z50 engine.

Bearing 16100 (ZA50 engine)∙ For ZA50 engine.
∙ For crankcase cover main gear.
∙ Outer diameter:28mm.
∙ Inner diameter:10mm.
∙ Width:8mm.
∙ NSK.

Bearing 6002 (ZA50 engine)∙ For ZA50 engine.
∙ For crankcase cover clutch drum.
∙ Outer diameter:32mm.
∙ Inner diameter:15mm.
∙ Width:9mm.
∙ NSK.

Bearing 6005 C3 (ZA50 engine)∙ For ZA50 engine.
∙ For main gear.
∙ Outer diameter:47mm.
∙ Inner diameter:25mm.
∙ Width:12mm.
∙ FAG.

Bearing E20 (ZA50 engine)∙ For ZA50 engine.
∙ For crankshaft right side.
∙ Outer diameter:47mm.
∙ Inner diameter:20mm.
∙ Width:12mm.
∙ NSK.

Needlebearing shift axle 16x22x12 (ZA50 engine)∙ For ZA50 engine.
∙ For the shift axle (Internally)
∙ A Piece (2 Needed)

Needlebearing drive shaft B-810 12.7x17.46x15.88 (ZA50 engine)∙ For ZA50 engine.
∙ Needlebearing B-810 Koyo Torrington.
∙ 12.7x17.46x15.88.
∙ For drive shaft.
∙ A piece (2 Needed)

Starter unit (ZA50 engine)

∙ For Puch ZA50 engine.
∙ Complete starter unit.
∙ Guide nut, Pull bolt, Starter cable.

Oil fill plug black (ZA50/Z50 engine)

∙ For Puch ZA50/Z50/MV/VS/DS engine.
∙ Plastic/Rubber.
∙ Black.

Oil fill plug grey (ZA50/Z50 engine)

∙ For Puch ZA50/Z50/MV/VS/DS engine.
∙ Plastic/Rubber.
∙ Grey.

Shift Dampers Extra stiff (ZA50 engine)

Voor Puch ZA50 motor.
Top Qaulity!
These shift dampers are a lot stiffer than the red shift dampers, because of this they are better suited for high performance engines like Polini and…

Shift Dampers (ZA50 engine)

∙ Voor Puch ZA50 motor.
∙ Top Qaulity!
∙ Beter Qaulity as original.

Rubber thule starter unit/brake light switch (ZA50 engine)

∙ For Puch ZA50 engine starter unit/brake light switch and spark plug cable.
∙ Rubber.
∙ Length:45mm.
∙ Diameter:19/10mm.
∙ Universal.

15mm Manifold (ZA50 engine)

∙ For Puch ZA50 engine.
∙ Inlet:15mm.
∙ Connection diameter:20mm (Bing carburetors)
∙ Total height:62mm.

12mm Manifold (ZA50 engine)

∙ For Puch ZA50 engine.
∙ Inlet:12mm.
∙ Connection diameter:20mm (Bing carburetors)
∙ Total height:62mm.

15mm Manifold MLM (ZA50 engine)

∙ For Puch ZA50 engine.
∙ Inlet:15mm.
∙ Connection diameter:20mm (Bing carburetors)
∙ Connection diameter without rubber:17mm.
∙ Total height:62mm.
∙ MLM.

Front sprocket 19 Tooth (ZA50 engine)∙ For ZA50 engine (Doesn't fit on a e50 engine!)
∙ 19 Tooth.

Front sprocket 20 Tooth (ZA50 engine)∙ For ZA50 engine (Doesn't fit on a e50 engine!)
∙ 20 Tooth.

Front sprocket 21 Tooth (ZA50 engine)∙ For ZA50 engine (Doesn't fit on a e50 engine!)
∙ 21 Tooth.

Shim washer for crankshaft with L17 and BO17 bearings (17x24x0.1)

∙ 17x24x0.1
∙ For shimming crankshafts with L17 en BO17 bearings.
∙ A Piece.

Shim washer for crankshaft with L17 and BO17 bearings (17x24x0.2)

∙ 17x24x0.2
∙ For shimming crankshafts with L17 en BO17 bearings.
∙ A Piece.

Shim washer for crankshaft with L17 and BO17 bearings (17x24x0.3)

∙ 17x24x0.3
∙ For shimming crankshafts with L17 en BO17 bearings.
∙ A Piece.

Shim washer for crankshaft with L17 and BO17 bearings (17x24x0.5)

∙ 17x24x0.5
∙ For shimming crankshafts with L17 en BO17 bearings.
∙ A Piece.

Shim washer for crankshaft with L17 and BO17 bearings (17x24x1.0)

∙ 17x24x1.0
∙ For shimming crankshafts with L17 en BO17 bearings.
∙ A Piece.

Shim washer for crankshaft with L17 and BO17 bearings (17x24x1.5)

∙ 17x24x1.5.
∙ For shimming crankshafts with L17 en BO17 bearings.
∙ A Piece.